Well, I am not sure if I am running kwboot correctly I am login into the wdex4100 via serial connection. and that where io am seeing the error
BootROM - 1.73
Booting from NAND flash
mvBoardIdGet: TWSI Read for Marvell Board ID failed (57)
Using default board ID
General initialization - Version: 1.0.0
Detected Device ID 6828
High speed PHY - Version: 2.0
Initialize DB-88F6820-BP board topology
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 00 | SGMII1 |
| 2 | 06 | SATA1 |
| 3 | 06 | SATA3 |
| 4 | 05 | USB3 HOST0 |
| 5 | 06 | SATA2 |
--------------------------------
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 1 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.06 (Jan 08 2015 - 10:04:46) Marvell version: 2014_T3.0p6
mvBoardSatRRead: Error: Read from S@R failed
mvBoardSatRRead: Error: Read from S@R failed
mvBoardSatRRead: Error: Read from S@R failed
Board: DB-88F6820-BP
SoC: MV88F6828 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1600 [MHz]
L2 @ 800 [MHz]
TClock @ 200 [MHz]
DDR @ 800 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 2 GiB
Map: Code: 0x7fece000:0x7ff95d44
BSS: 0x7ffef254
Stack: 0x7f9cdf20
Heap: 0x7f9ce000:0x7fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dcad ,512 MiB
MMC: mv_sdh: 0
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00001f500000-0x00001ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 3/1
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 36 (0x00000024)...
Done
lan mac_addr : 00 90 a9 e4 89 34
Set lan 0 WakeOnLan ok
Set lan 1 WakeOnLan ok
MicroP Enable HD
Enable HD1
Enable HD2
Enable HD3
Enable HD4
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x00 |
| egiga1 | SGMII | 0x01 |
egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x500000, size 0x500000
5242880 bytes read: OK
NAND read: device 0 offset 0xa00000, size 0x500000
5242880 bytes read: OK
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: Linux-388
Created: 2018-11-16 6:11:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4093524 Bytes = 3.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 00f00000 ...
Image Name: Ramdisk
Created: 2019-05-15 2:26:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2220263 Bytes = 2.1 MiB
Load Address: 00e00000
Entry Point: 00e00000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
stopping USB..
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Fri Nov 16 14:11:47 CST 2018 2014T30p5 Build-git0451941
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 1 pages/cpu @c0b10000 s8320 r8192 d16256 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65505
Kernel command line: root=/dev/ram console=ttyS0,115200
PID hash table entries: 4096 (order: -1, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 4, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 3, 262144 bytes)
allocated 524288 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 2048MB = 2048MB total
Memory: 2081984k/2081984k available, 15168k reserved, 1303552K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff8000 ( 32 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xfff00000 ( 247 MB)
lowmem : 0xc0000000 - 0xf0700000 ( 775 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0714270 (7217 kB)
.init : 0xc0718000 - 0xc075a080 ( 265 kB)
.data : 0xc075c000 - 0xc07a7e40 ( 304 kB)
.bss : 0xc07a7e40 - 0xc0871570 ( 806 kB)
Hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
NR_IRQS:16 nr_irqs:16 16
LSP version: linux-3.10.39-2014_T3.0p5
sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
Console: colour dummy device 80x30
Calibrating delay loop... 3188.32 BogoMIPS (lpj=15941632)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 4096
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0xc056c250 - 0xc056c2a8
mvebu-pmsu: Initializing Power Management Service Unit
Initializing CPU Reset module
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (6376.65 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
xor: measuring software checksum speed
arm4regs : 1708.800 MB/sec
8regs : 1129.600 MB/sec
32regs : 1104.000 MB/sec
xor: using function: arm4regs (1708.800 MB/sec)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated
bio: create slab <bio-0> at 0
raid6: int32x1 427 MB/s
raid6: int32x2 417 MB/s
raid6: int32x4 537 MB/s
raid6: int32x8 461 MB/s
raid6: using algorithm int32x4 (537 MB/s)
raid6: using intx1 recovery algorithm
mvebu-pcie pcie-controller.3: PCIe0.0: link down
mvebu-pcie pcie-controller.3: PCIe1.0: link down
mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers enabled
PCI: bus2: Fast back to back transfers enabled
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:02.0: PCI bridge to [bus 02]
PCI: enabling device 0000:00:01.0 (0140 -> 0143)
PCI: enabling device 0000:00:02.0 (0140 -> 0143)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Switching to clocksource armada_370_xp_clocksource
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 1, 65536 bytes)
TCP bind hash table entries: 8192 (order: 1, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 1024 (order: 0, 32768 bytes)
UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2112K (c0f08000 - c1118000)
bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 8192 (order 0, 32768 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.22)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 1524
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr )
mv_xor f1060800.xor: freeing 1 in use descriptors!
mv_xor f1060800.xor: Marvell XOR: ( crc32c )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr )
mv_xor f1060900.xor: freeing 1 in use descriptors!
mv_xor f1060900.xor: Marvell XOR: ( crc32c )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
console [ttyS0] enabled
f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A
brd: module loaded
loop: module loaded
ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi0 : ahci_mv_platform
scsi1 : ahci_mv_platform
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
ahci_mv f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci_mv f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi2 : ahci_mv_platform
scsi3 : ahci_mv_platform
ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 60
ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 60
armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: bad block at 0x000006960000
8 ofpart partitions found on MTD device armada-nand
Creating 8 MTD partitions on "armada-nand":
0x000000000000-0x000000500000 : "U-Boot"
0x000000500000-0x000000a00000 : "uImage"
0x000000a00000-0x000000f00000 : "uRamdisk"
0x000000f00000-0x00001c800000 : "image.cfs"
0x00001c800000-0x00001d700000 : "rescue fw"
0x00001d700000-0x00001eb00000 : "config"
0x00001eb00000-0x00001f500000 : "reserve1"
0x00001f500000-0x00001ff00000 : "reserve2"
SoC: model = 0x6828, revision = 0x4
mvPncVirtBase = 0xf0e00000, pncTcamSize = 1024
o 3 Giga ports supported
o SKB recycle supported (Disabled)
o NETA acceleration mode 4
o BM supported for CPU: 4 BM pools
o PnC supported (Enabled)
o RX Queue support: 8 Queues * 256 Descriptors
o TX Queue support: 8 Queues * 532 Descriptors
o GSO supported
o GRO supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Driver DEBUG statistics enabled
port #0: is_sgmii=0, is_rgmii=1, phy_addr=0
o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800
o Port 0 is connected to Linux netdevice
o egiga0, ifindex = 2, GbE port = 0
giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform)
port #1: is_sgmii=1, is_rgmii=0, phy_addr=1
o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048
o Port 1 is connected to Linux netdevice
o egiga1, ifindex = 3, GbE port = 1
giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform)
libphy: orion_mdio_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 50, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
ata2: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
usb 2-1: new high-speed USB device number 2 using xhci-hcd
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
dm_crypt using the OCF package.
cpuidle: using governor ladder
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0)
mvCesaInit: channels=2, session=640, queue=256
armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode
cesadev_init(c0734f0c)
TCP: cubic registered
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
registered taskstats version 1
mvebu-rtc f10a3800.rtc: setting system clock to 2019-06-18 02:37:27 UTC (1560825447)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 256K (c0718000 - c0758000)
init started: BusyBox v1.20.2 (2014-10-30 15:28:01 CST)
starting pid 1256, tty '': '/etc/rc.sh'
** Mounting /etc/fstab
umount: can't umount /proc: Invalid argument
umount: can't umount /usr/local/modules: Invalid argument
offset_flag=1,vaule_flag=1,bit_fUBI: attaching mtd5 to ubi0
lag=1
reg f1018140 : 00700000
UBI: scanning is finished
UBI: attached mtd5 (name "config", size 20 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 160, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 48/30, WL threshold: 4096, image sequence number: 1237890639
UBI: available PEBs: 12, total reserved PEBs: 148, PEBs reserved for bad PEB handling: 20
UBI: background thread "ubi_bgt0d" started, PID 1271
UBI device number 0, total 160 LEBs (20316160 bytes, 19.4 MiB), available 12 LEBs (1523712 bytes, 1.5 MiB), LEB size 126976 bytes (124.0 KiB)
UBIFS: background thread "ubifs_bgt0_0" started, PID 1276
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "config"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 14475264 bytes (13 MiB, 114 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS: reserved for root: 683702 bytes (667 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 761978AF-C5F8-4E6F-893E-5B2783EE2E98, small LPT model
umount: can't umount /usr/local/tmp/image.cfs: No such file or directory
rm: can't remove '/usr/local/tmp/image.cfs': No such file or directory
umount: can't umount /usr/local/tmp: Invalid argument
first good block is 0
image len = 98234368 , image checksum = 578057a0
umount: can't umount /usr/local/tmp: Invalid argument
usb 2-1.2: new high-speed USB device number 3 using xhci-hcd
usb-storage 2-1.2:1.0: USB Mass Storage device detected
scsi4 : usb-storage 2-1.2:1.0
scsi 4:0:0:0: Direct-Access VendorCo ProductCode 2.00 PQ: 0 ANSI: 4
sd 4:0:0:0: [sda] 30720000 512-byte logical blocks: (15.7 GB/14.6 GiB)
sd 4:0:0:0: Attached scsi generic sg0 type 0
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] No Caching mode page found
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] No Caching mode page found
sd 4:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 4:0:0:0: [sda] No Caching mode page found
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] Attached SCSI removable disk
dump image checksum=578057a0
mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules
cp: can't stat '/tmp1/*': No such file or directory
ln: /lib/./liblber-2.4.so.2.5.6: File exists
ln: /lib/./libminiupnpc.so: File exists
ln: /lib/./libnatpmp.so: File exists
ln: /lib/./libpam.so.0.81.6: File exists
ln: /usr/local/sbin/alert_email_config.sh: File exists
ln: /usr/sbin/language.sh: File exists
ln: /lib/libnss_winbind.so.2: File exists
dev.raid.speed_limit_max = 1000
egiga0 Link encap:Ethernet HWaddr 00:50:43:02:02:01
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:193
egiga0: mac address changed
egiga1 Link encap:Ethernet HWaddr 00:50:43:02:02:02
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:194
Do Lan Port Switch
egiga1: mac address changed
not_egiga0: mac address changed
jnl: driver (lke_9.2.0 lke_9.2.0_r256412_b49, LBD=ON) loaded at bf000000
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd:: trace mask set to 0000000f
ufsd: driver (lke_9.2.0 lke_9.2.0_r256412_b49, build_host("fsd-linux-bs06b"), acl, ioctl, bdi, sd2(0), fua, bz, tr, rsrc) loaded at bf020000
NTFS support included
exFAT support included
Hfs+/HfsJ support included
optimized: speed
Build_for__WD_Yellowstone_k3.10.39_2015-07-06_lke_9.2.0_r256412_b49
bio: create slab <bio-1> at 1
Btrfs loaded
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
lrwxrwxrwx 1 root 0 17 Jun 18 02:37 [1;36m/usr/sbin//raid_config[0m -> [1;32m/usr/sbin/diskmgr[0m
lrwxrwxrwx 1 root 0 17 Jun 18 02:37 [1;36m/usr/sbin//raid_expand[0m -> [1;32m/usr/sbin/diskmgr[0m
lrwxrwxrwx 1 root 0 17 Jun 18 02:37 [1;36m/usr/sbin//raid_expand_disks[0m -> [1;32m/usr/sbin/diskmgr[0m
lrwxrwxrwx 1 root 0 17 Jun 18 02:37 [1;36m/usr/sbin//raid_update_info[0m -> [1;32m/usr/sbin/diskmgr[0m
hardware init
Read PCI register offset 0x18140 = 701000
Read PCI register offset 0x18140 = 701000
Read PCI register offset 0x18140 = 701000
Resetting USB device /dev/bus/usb/003/002
usb 3-1: reset SuperSpeed USB device number 2 using xhci-hcd
usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
xhci-hcd f10f0000.usb3: xHCI xhci_drop_endpoint called with disabled ep ee3238c0
Reset successful
mode nmae: -->WDMyCloudEX4100<--
Set 802.3az
mtd check v1.06.06032015
config mtd type is UBIFS
device = /usr/local/config
Total size = 12384 Kbytes
Used size = 276 Kbytes
Free size = 12108 Kbytes
percentage = 2
/usr/local/config free size is 12398592
/usr/local/config/dynamicconfig_config.ini file size is zero , and copy from default
** copy config files
*** Copy orion.db from flash ****
cp: can't stat '/usr/local/modules/files/fan_temperature.txt': No such file or directory
*** symlink onbrd.ini from flash ****
/etc/sysinit.d/wdlog: line 13: /etc/system.conf: No such file or directory
** set loopback interface
UBI: attaching mtd6 to ubi1
UBI: scanning is finished
UBI: attached mtd6 (name "reserve1", size 10 MiB) to ubi1
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2557296595
UBI: available PEBs: 18, total reserved PEBs: 62, PEBs reserved for bad PEB handling: 24
UBI: background thread "ubi_bgt1d" started, PID 3279
UBI device number 1, total 80 LEBs (10158080 bytes, 9.7 MiB), available 18 LEBs (2285568 bytes, 2.2 MiB), LEB size 126976 bytes (124.0 KiB)
UBIFS: background thread "ubifs_bgt1_0" started, PID 3298
UBIFS: mounted UBI device 1, volume 0, name "reserve"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 3047424 bytes (2 MiB, 24 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS: reserved for root: 143937 bytes (140 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2AF1DBDC-311B-44DB-82D0-0BB16F030BA5, small LPT model
UBIFS: un-mount UBI device 1, volume 0
UBIFS: background thread "ubifs_bgt1_0" stops
UBI: attaching mtd7 to ubi2
UBI: scanning is finished
UBI: attached mtd7 (name "reserve2", size 10 MiB) to ubi2
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 540768837
UBI: available PEBs: 6, total reserved PEBs: 74, PEBs reserved for bad PEB handling: 28
UBI: background thread "ubi_bgt2d" started, PID 3313
UBI device number 2, total 80 LEBs (10158080 bytes, 9.7 MiB), available 6 LEBs (761856 bytes, 744.0 KiB), LEB size 126976 bytes (124.0 KiB)
mknod: /dev/mtd7: File exists
UBIFS: background thread "ubifs_bgt2_0" started, PID 3326
UBIFS: mounted UBI device 2, volume 0, name "reserve2"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 4063232 bytes (3 MiB, 32 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS: reserved for root: 191915 bytes (187 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID DA06F613-BDF8-4D03-A522-E6A18E2007CF, small LPT model
/dev/mtd7 mount ok(ubi)
UBIFS: un-mount UBI device 2, volume 0
UBIFS: background thread "ubifs_bgt2_0" stops
mac1 = 00:90:A9:E4:89:34
mac2 =egiga0: mac address changed
00:90:A9:E4:89:35
lan0:ifconfiegiga1: mac address changed
g egiga0 hw ether 00:90:A9:E4:89:34
lan0:ifconfig egiga1 hw ethpool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
er 00:90:A9:E4:8egiga0: link up
9:35
egiga0: link up, full duplex, speed 1 Gbps
egiga0: started
pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
egiga1: started
set lan0 speed
set lan1 speed
[wd_read_serial.c:621] Read serial number from flash.
[wd_read_serial.c:160] serial number : WNAG29070174
hidden encryption: 0
old firmware ver:2.31.183.0514.2019
new firmware ver:2.31.183.0514.2019
rm: can't remove '/tmp/fix_wd_config': No such file or directory
NET: Registered protocol family 10
IPv6: ADDRCONF(NETDEV_UP): egiga1: link is not ready
sit: Unknown symbol ip_tunnel_get_stats64 (err 0)
insmod: error inserting '/usr/local/modules/driver/sit.ko': -1 Unknown symbol in module
rm: can't remove '/bin/sysctl': No such file or directory
net.ipv6.conf.default.accept_dad = 2
net.ipv6.conf.egiga0.accept_dad = 2
net.ipv6.conf.default.dad_transmits = 1
net.ipv6.conf.egiga0.dad_transmits = 1
net.ipv6.conf.default.forwarding = 0
net.ipv6.conf.default.accept_redirects = 1
mkdir: can't create directory '/usr/local/etc': File exists
*** execute rc.init.sh
ip.sh bonding {1 restart}
bonding starting ...
insmod /usr/local/modules/driver/bonding.ko mode=1 miimon=500 use_carrier=1 downdelay=1000 updelay=1000
bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
bonding: MII link monitoring set to 500 ms
8021q: adding VLAN 0 to HW filter on device bond0
IPv6: ADDRCONF(NETDEV_UP): bond0: link is not ready
egiga0: stopped
egiga0: mac address changed
egiga0: link up
egiga0: started
bonding: bond0: enslaving egiga0 as a backup interface with an up link.
egiga1: stopped
egiga1: mac address changed
egiga1: started
bonding: bond0: enslaving egiga1 as a backup interface with a down link.
udhcpc (v1.20.2) started
cat: can't open '/tmp/setip.0': No such file or directory
Sending discover...
killall: crond: no process killed
crond[3575]: crond: crond (busybox 1.20.2) started, log level 8
--2019-06-18 02:37:58-- http://download.wdc.com/nas/WDMyCloudEX4100_HDD_Blacklist.xml
Resolving download.wdc.com... failed: Name or service not known.
wget: unable to resolve host address 'download.wdc.com'
[upnp_nas_xml.c() 348] Can't get IP of bond0
Initializing UPnP Sdk with
ipaddress = (null) port = 0
UPnP Initialized
ipaddress= 0.0.0.0 port = 49152
Specifying the webserver root directory -- /etc/upnp
Registering the RootDevice
with desc_doc_url: http://0.0.0.0:49152/nasdevicedesc.xml
RootDevice Registered
Initializing State Table
State Table Initialized
sh: you need to specify whom to kill
Advertisements Sent
bonding: bond0: link status definitely up for interface egiga0, 1000 Mbps full duplex.
bonding: bond0: making interface egiga0 the new active one.
bonding: bond0: first active interface up!
IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
*** Copy CacheVolume data from flash ****
*** set Time Zone ****
$Usage: apache {start|stop|restart} {web/dav}
Tue Jun 18 02:37:59 PDT 2019
*** get Time from rtc and set it into system ****
rtc: RTC time = 2019/6/18 Tue 2:38:0
Mon Jun 17 19:38:00 PDT 2019
Set Date & time : sntp -K /dev/null -S -r time.windows.com
sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8)
time.windows.com lookup error Name or service not known
Module IPC SERVER Version:(1.00.20090706)
ads=0
created mail daemon thread 0
restart sysinfod...
Sending discover...
Sending select for 10.0.0.8...
Lease of 10.0.0.8 obtained, lease time 604800
deleting routers
route: SIOCDELRT: No such process
call load_module network
RTNETLINK answers: Operation not supported
RTNETLINK answers: Operation not supported
POWER ON DEVICE!!
sh: can't create /sys/module/gpio/parameters/hdd_status: nonexistent directory
cp: can't stat '/usr/local/config/user.log.*': No such file or directory
cp: can't stat '/usr/local/config/wdmcserver.log.*': No such file or directory
cp: can't stat '/usr/local/config/orion_cm.log.*': No such file or directory
cp: can't stat '/usr/local/config/mycloud.log.*': No such file or directory
cp: can't stat '/usr/local/config/wdhwlib.log.*': No such file or directory
mount: mount point /proc/bus/usb does not exist
WD hwlib start..............
Starting system message bus
Starting wdtms
wdtms started
Loading x_tables.ko
Loading nf_conntrack.ko
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
Loading xt_conntrack.ko
Loading xt_state.ko
Loading xt_tcpudp.ko
Loading xt_recent.ko
Loading xt_LOG.ko
Loading xt_limit.ko
Loading ip_tables.ko
ip_tables: (C) 2000-2006 Netfilter Core Team
Loading iptable_filter.ko
Loading nf_defrag_ipv4.ko
Loading nf_conntrack_ipv4.ko
Loading ip6_tables.ko
ip6_tables: (C) 2000-2006 Netfilter Core Team
Loading ip6table_filter.ko
Loading nf_defrag_ipv6.ko
Loading nf_conntrack_ipv6.ko
PHY_LAN_NUMBER=2
BOND_ENABLE=1
VLAN0_ENABLE=0
VLAN1_ENABLE=0
I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml"
--2019-06-17 19:38:03-- http://download.wdc.com/apps/WDMyCloudEX4100/WDMyCloudEX4100.xml
Resolving download.wdc.com... 34.211.97.143, 35.160.19.99
Connecting to download.wdc.com|34.211.97.143|:80... cat: can't open '/var/run/traceroute_wd.pid': No such file or directory
ash: you need to specify whom to kill
killall: traceroute: no process killed
connected.
HTTP request sent, awaiting response...
-------------use hwlib instead of fan_control b c-------------
200 OK
Length: 62016 (61K) [text/xml]
Saving to: '/var/www/xml/app_info.xml'
100%[======================================>] 62,016 281KB/s in 0.2s
2019-06-17 19:38:04 (281 KB/s) - '/var/www/xml/app_info.xml' saved [62016/62016]
I/O warning : failed to load external entity "/var/www/xml/app_update.xml"
Set Date & time : sntp -K /dev/null -S -r pool.ntp.org
[ERROR] Unable to open (null)
sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8)
2019-06-17 19:38:05.071049 (+0800) +0.947954 +/- 0.661103 pool.ntp.org 67.217.112.181 s2
NTP Server connected successfully!!!
rtc: system time: 2019/6/18 Tue 2:38:10
setRTCTime
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda1): using internal journal
EXT3-fs (sda1): recovery complete
EXT3-fs (sda1): mounted filesystem with ordered data mode
waiting : [10]
country=0
lang_path=/usr/local/modules/language
chk_io v1.04.20141112
system daemon v1.04.20141211
PIP is disabled, exiting.
Mon Jun 17 19:38:53 PDT 2019 - %I - Communication Manager - Start
dev.raid.speed_limit_max = 200000
starting pid 5224, tty '/dev/ttyS0': '/bin/login'
Password of admin:
sh: operate_auth: not found
killall: chk_hotplug: no process killed
call load_module
### create systemfile ###
### sata_reload_application start ###
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
New interface iface0 added
iface0 updated.
New interface iface1 added
iface1 updated.
New interface ifbond added
ifbond updated.
Initializing UPnP Sdk with
ipaddress = (null) port = 0
UPnP Initialized
ipaddress= 10.0.0.8 port = 49152
Specifying the webserver root directory -- /etc/upnp
Registering the RootDevice
with desc_doc_url: http://10.0.0.8:49152/nasdevicedesc.xml
RootDevice Registered
Initializing State Table
State Table Initialized
Starting atopacctd
cannot switch on process accounting: Function not implemented
Starting atop system monitor atop
atop started
Advertisements Sent
*** APKG Daemon is starting ... ***
Rename is FAILE
USE 2nd Rename
sh: you need to specify whom to kill
sh: you need to specify whom to kill
Rename is FAILE
USE 2nd Rename
killall: smbd: no process killed
Starting wdnotifier
wdnotifier started
killall: smbd: no process killed
killall: chk_blockip: no process killed
killall: chk_blockip: no process killed
sh: syntax error: unexpected "("
Starting AFP services:
I/O warning : failed to load external entity "/mnt/USB/USB2_a1/.timeMachine.xml"
Document parsed unsuccessfully.
3901 root 8640 S avahi-daemon: running [WDMyCloudEX4100.local]
killall: elephantdriveDaemon: no process killed
Setting up docker
mkdir: can't create directory '/mnt/HD/HD_a2/Nas_Prog/_docker': No such file or directory
Loading drivers
Loading /usr/local/modules/driver/nf_conntrack.ko
insmod: error inserting '/usr/local/modules/driver/nf_conntrack.ko': -1 File exists
failed to load /usr/local/modules/driver/nf_conntrack.ko
Loading /usr/local/modules/driver/nf_nat.ko
Loading /usr/local/modules/driver/nf_defrag_ipv4.ko
insmod: error inserting '/usr/local/modules/driver/nf_defrag_ipv4.ko': -1 File exists
failed to load /usr/local/modules/driver/nf_defrag_ipv4.ko
Loading /usr/local/modules/driver/nf_conntrack_ipv4.ko
insmod: error inserting '/usr/local/modules/driver/nf_conntrack_ipv4.ko': -1 File exists
failed to load /usr/local/modules/driver/nf_conntrack_ipv4.ko
Loading /usr/local/modules/driver/nf_nat_ipv4.ko
Loading /usr/local/modules/driver/x_tables.ko
insmod: error inserting '/usr/local/modules/driver/x_tables.ko': -1 File exists
failed to load /usr/local/modules/driver/x_tables.ko
Loading /usr/local/modules/driver/xt_conntrack.ko
insmod: error inserting '/usr/local/modules/driver/xt_conntrack.ko': -1 File exists
failed to load /usr/local/modules/driver/xt_conntrack.ko
Loading /usr/local/modules/driver/xt_addrtype.ko
Loading /usr/local/modules/driver/xt_tcpudp.ko
insmod: error inserting '/usr/local/modules/driver/xt_tcpudp.ko': -1 File exists
failed to load /usr/local/modules/driver/xt_tcpudp.ko
Loading /usr/local/modules/driver/xt_nat.ko
Loading /usr/local/modules/driver/nf_nat_masquerade_ipv4.ko
insmod: can't read '/usr/local/modules/driver/nf_nat_masquerade_ipv4.ko': No such file or directory
failed to load /usr/local/modules/driver/nf_nat_masquerade_ipv4.ko
Loading /usr/local/modules/driver/ipt_MASQUERADE.ko
Loading /usr/local/modules/driver/ip_tables.ko
insmod: error inserting '/usr/local/modules/driver/ip_tables.ko': -1 File exists
failed to load /usr/local/modules/driver/ip_tables.ko
Loading /usr/local/modules/driver/iptable_filter.ko
insmod: error inserting '/usr/local/modules/driver/iptable_filter.ko': -1 File exists
failed to load /usr/local/modules/driver/iptable_filter.ko
Loading /usr/local/modules/driver/iptable_nat.ko
Loading /usr/local/modules/driver/llc.ko
Loading /usr/local/modules/driver/stp.ko
Loading /usr/local/modules/driver/bridge.ko
Bridge firewalling registered
Loading /usr/local/modules/driver/br_netfilter.ko
insmod: can't read '/usr/local/modules/driver/br_netfilter.ko': No such file or directory
failed to load /usr/local/modules/driver/br_netfilter.ko
Setting up cgroup
Get http:///var/run/docker.sock/v1.19/containers/json: dial unix /var/run/docker.sock: no such file or directory. Are you trying to connect to a TLS-enabled daemon without TLS?
wdappmgr_auto_start finished modifying wd apps exit code
Starting Docker
Docker is not setup! Run docker_daemon.sh setup
umount: /mnt/HD/HD_a2/Nas_Prog/_docker/devicemapper: not found
Total RAM: 2084352 KB
Creating /sys/fs/cgroup/memory/docker
Docker quota: 1042176 KB
Set memory quota for docker: 1067188224
/usr/sbin/docker_daemon.sh: line 198: /var/lib/docker/docker.log: No such file or directory
Docker pid 6094
Stopping wdappmgr
wdappmgr is already stopped
Starting wdappmgr
parent exiting!
wdappmgr started
curl: (7) Couldn't connect to server
curl: (7) Couldn't connect to server
curl: (7) Couldn't connect to server
curl: (7) Couldn't connect to server
curl: (7) Couldn't connect to server
country=0
lang_path=/usr/local/modules/language
### sata_reload_application end ###
Create USB dev node
rm: can't remove '/tmp/disk_uuid': No such file or directory
dry_total_size:3761
dry_total_size:0
dry_total_size:49607
dry_total_size:3183
dry_total_size:4152
LED_POWER_ON
^[[A^[[A^H^H^HLogin incorrect
Password of admin:
BusyBox v1.20.2 (2014-10-30 15:28:01 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@WDMyCloudEX4100 / # ls
[1;34mCacheVolume[0m [1;34mhome[0m [1;34mmnt[0m [1;34mroot[0m [1;34mtmp[0m
[1;34mbin[0m [1;34mlib[0m [1;36mnfs[0m [1;34msbin[0m [1;34musr[0m
[1;34mdev[0m [1;36mlinuxrc[0m [1;34mopt[0m [1;34mshares[0m [1;34mvar[0m
[1;34metc[0m [1;34mlost+found[0m [1;34mproc[0m [1;34msys[0m
root@WDMyCloudEX4100 / # ls
[1;34mCacheVolume[0m [1;34mhome[0m [1;34mmnt[0m [1;34mroot[0m [1;34mtmp[0m
[1;34mbin[0m [1;34mlib[0m [1;36mnfs[0m [1;34msbin[0m [1;34musr[0m
[1;34mdev[0m [1;36mlinuxrc[0m [1;34mopt[0m [1;34mshares[0m [1;34mvar[0m
[1;34metc[0m [1;34mlost+found[0m [1;34mproc[0m [1;34msys[0m
root@WDMyCloudEX4100 / # ls
[1;34mCacheVolume[0m [1;34mhome[0m [1;34mmnt[0m [1;34mroot[0m [1;34mtmp[0m
[1;34mbin[0m [1;34mlib[0m [1;36mnfs[0m [1;34msbin[0m [1;34musr[0m
[1;34mdev[0m [1;36mlinuxrc[0m [1;34mopt[0m [1;34mshares[0m [1;34mvar[0m
[1;34metc[0m [1;34mlost+found[0m [1;34mproc[0m [1;34msys[0m
root@WDMyCloudEX4100 / # [Jls -lah
drwxr-xr-x 19 root root 1.0K Jun 17 19:39 [1;34m.[0m
drwxr-xr-x 19 root root 1.0K Jun 17 19:39 [1;34m..[0m
-rw------- 1 root root 11 Jun 17 19:40 [0;0m.ash_history[0m
-rw------- 1 root root 1.0K Jun 17 19:37 [0;0m.rnd[0m
drwxr-xr-x 3 root root 1.0K Jun 17 19:37 [1;34mCacheVolume[0m
drwxr-xr-x 2 root root 1.0K Jun 17 19:37 [1;34mbin[0m
drwxrwxrwt 7 root root 14.0K Jun 17 19:39 [1;34mdev[0m
drwxr-xr-x 25 root root 2.0K Jun 17 19:39 [1;34metc[0m
drwxr-xr-x 4 root root 1.0K May 14 19:26 [1;34mhome[0m
drwxr-xr-x 2 root root 12.0K Jun 17 19:37 [1;34mlib[0m
lrwxrwxrwx 1 root root 11 May 14 19:26 [1;36mlinuxrc[0m -> [1;32mbin/busybox[0m
drwx------ 2 root root 12.0K May 14 19:26 [1;34mlost+found[0m
drwxrwxrwt 5 root root 100 Jun 17 19:37 [1;34mmnt[0m
lrwxrwxrwx 1 root root 7 Jun 17 19:39 [1;36mnfs[0m -> [1;34m/shares[0m
drwxr-xr-x 2 root root 1.0K Jun 17 19:37 [1;34mopt[0m
dr-xr-xr-x 127 root root 0 Dec 31 1969 [1;34mproc[0m
drwxr-xr-x 2 root root 1.0K May 14 19:26 [1;34mroot[0m
drwxr-xr-x 2 root root 1.0K Jun 17 19:37 [1;34msbin[0m
drwxrwxrwx 2 root root 1.0K Jun 17 19:38 [1;34mshares[0m
dr-xr-xr-x 12 root root 0 Jun 17 19:37 [1;34msys[0m
drwxrwxrwt 12 root root 1.1K Jun 17 19:39 [1;34mtmp[0m
drwxr-xr-x 7 root root 1.0K Jun 17 19:37 [1;34musr[0m
drwxr-xr-x 13 root root 1.0K Jun 17 19:39 [1;34mvar[0m
root@WDMyCloudEX4100 / # cd //
root@WDMyCloudEX4100 / # ls
[1;34mCacheVolume[0m [1;34mhome[0m [1;34mmnt[0m [1;34mroot[0m [1;34mtmp[0m
[1;34mbin[0m [1;34mlib[0m [1;36mnfs[0m [1;34msbin[0m [1;34musr[0m
[1;34mdev[0m [1;36mlinuxrc[0m [1;34mopt[0m [1;34mshares[0m [1;34mvar[0m
[1;34metc[0m [1;34mlost+found[0m [1;34mproc[0m [1;34msys[0m
root@WDMyCloudEX4100 / # cd home
root@WDMyCloudEX4100 /home # ls
[1;34mroot[0m [1;34msqueezecenter[0m
root@WDMyCloudEX4100 /home # cd root/[J
root@WDMyCloudEX4100 root # ls
[0;0marchive-name.tar.gz[0m
root@WDMyCloudEX4100 root # ls[J[[Jedefefefefefefefef.gz ./[J[25Dxvf archive-name.tar.gz ./[25D
-sh: ledefefefefefefefef: not found
root@WDMyCloudEX4100 root # tar
BusyBox v1.20.2 (2014-10-30 15:28:01 CST) multi-call binary.
Usage: tar -[cxtzjhmvO] [-X FILE] [-T FILE] [-f TARFILE] [-C DIR] [FILE]...
Create, extract, or list files from a tar file
Operation:
c Create
x Extract
t List
f Name of TARFILE ('-' for stdin/out)
C Change to DIR before operation
v Verbose
z (De)compress using gzip
j (De)compress using bzip2
O Extract to stdout
h Follow symlinks
m Don't restore mtime
exclude File to exclude
X File with names to exclude
T File with names to include
root@WDMyCloudEX4100 root # tar -zxvf archive-name.tar.gz ./
./
./._kwboot
./kwboot
./archive
./._u-boot-a38x-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin
./u-boot-a38x-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin
./._kwboot.1
./kwboot.1
./x
root@WDMyCloudEX4100 root # ls
[0;0marchive[0m
[0;0marchive-name.tar.gz[0m
[1;32mkwboot[0m
[0;0mkwboot.1[0m
[0;0mu-boot-a38x-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin[0m
[0;0mx[0m
root@WDMyCloudEX4100 root # kwboot
-sh: kwboot: not found
root@WDMyCloudEX4100 root # kwbootttt[t
-sh: kwt: not found
root@WDMyCloudEX4100 root # ./kwboot[J
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # ./kwboot[[J
-sh: ./kwboo: not found
root@WDMyCloudEX4100 root # ./kboo[[[J
-sh: ./kb: not found
root@WDMyCloudEX4100 root # ./kwboot
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin -s 0 -q 1
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin -s 0 -q 1[J
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
root@WDMyCloudEX4100 root # [Jld-6-nand-uart.bin -s 0 -q 1[J[1A
root@WDMyCloudEX4100 root # kwboot
-sh: kwboot: not found
root@WDMyCloudEX4100 root # chmod +x kwboot[J
root@WDMyCloudEX4100 root # kwboot
-sh: kwboot: not found
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin -s 0 -q 1[J
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin -s 0 -q 1[J
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x
-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin -s 0 -q 1[[[[[J
./kwboot: line 1: syntax error: unexpected ")"
root@WDMyCloudEX4100 root # exit
process '/bin/login' (pid 5224) exited. Scheduling for restart.
Please press Enter to activate this console. exit
starting pid 8948, tty '/dev/ttyS0': '/bin/login'
Password of admin:
Login incorrect
Password of admin: send alert suspending
[Disconnected]